Year 11 · Original DASKEREL extended lesson · Academic review pending
Electromagnets and the motor effect
Allow up to 55 minutes for reading, practice and review · Source route: Oak AQA Combined Science Higher; academic review required
DASKEREL wrote this resource using the Oak National Academy unit sequence as a curriculum reference. It is an extended lesson, not a complete unit or an exam-board-approved course. Academic review remains pending.
You will learn to
- Describe the magnetic field around a current-carrying wire and solenoid.
- Predict the effect of reversing current or field on the force on a conductor.
- Explain the purpose of a split-ring commutator in a simple d.c. motor.
Key terms: magnetic field · solenoid · electromagnet · motor effect · force · current · split-ring commutator
Teaching sequence
Check these ideas before you begin:
- Recognise north and south poles and describe a magnetic field pattern.
- Distinguish conventional current direction from movement of electrons in a metal.
1. Retrieve field patterns · about 8 minutes
Teach or study: Ask pupils to compare a straight wire, solenoid and bar magnet using direction-labelled sketches.
Try: Sketch a field around a wire and describe the field inside a solenoid.
2. Model the motor effect · about 12 minutes
Teach or study: Use a fixed field arrow and vary only current, then only field, while narrating the force change.
Try: Complete a two-variable reversal table and justify each force direction.
3. Use the left-hand rule · about 12 minutes
Teach or study: Orient thumb and fingers at right angles and explicitly identify conventional current, field and force.
Try: Label three arrows on two given conductor diagrams before predicting motion.
4. Explain continuous rotation · about 16 minutes
Teach or study: Trace a coil through half a turn and discuss how brushes and a split ring change its supply connections.
Try: Write a four-step explanation of how a simple d.c. motor continues to turn.
5. Check and correct · about 7 minutes
Teach or study: Use the exit ticket to diagnose confusion between field reversal and current reversal or commutator action.
Try: Answer both exit prompts and correct a mistaken motor description.
Learn the idea
A current in a wire creates a magnetic field around it. The field has circular lines around a straight wire, and its direction depends on the direction of current. Winding the wire into a solenoid concentrates the field; inside a long solenoid the field is strong and approximately uniform. An iron core can strengthen the electromagnet, and switching off the current switches off most of its magnetism. These statements describe an engineered device, not a permanent bar magnet. A field diagram communicates direction and pattern, while the closeness of drawn lines represents relative field strength rather than physical threads in space.
When a current-carrying conductor lies in another magnetic field, the fields interact and the conductor can experience a force. This is the motor effect. The conductor must be positioned so that the current is not parallel to the field for the familiar sideways force; when current and field are parallel the magnetic force is zero. Reversing the current while keeping the magnetic field the same reverses the force. Reversing the field alone does the same. Reversing both current and field restores the original force direction. Explain which variable changed before predicting movement; a memorised direction without a diagram is hard to justify.
Fleming's left-hand rule is a direction aid for the motor effect. Thumb represents force or motion, first finger the magnetic field from north to south, and second finger conventional current from positive to negative. Hold the three directions at right angles. The rule does not calculate how large the force is. A stronger magnetic field, a larger current or a longer conductor length within the field tends to increase the force, with other conditions held fixed. Never confuse conventional current with electron motion; electrons move the opposite way in a metal wire.
A simple d.c. motor places a current-carrying coil between magnetic poles. Opposite sides of the coil carry current in opposite directions and experience forces in opposite directions, giving a turning effect. After roughly half a turn, the coil's orientation has changed. A split-ring commutator reverses the connection to the supply each half-turn, reversing current in each coil side so the turning effect continues in the same rotational sense. Brushes maintain electrical contact as the ring turns. This is a model of a simple motor; real motors may have several coils and design details beyond this GCSE explanation.
Reasoning about a motor begins with the system boundary. Electrical energy is transferred to movement, but not all input energy becomes useful rotation; heating and sound can also occur. Increasing current can strengthen the motor effect, yet practical components have ratings and must be used under supervision. For a paper question, label current, field and force arrows before applying a rule. If one arrow reverses, track the consequence systematically rather than mentally spinning a three-dimensional diagram. Use a low-voltage classroom demonstration only under teacher control; never connect a model coil directly to mains electricity.
Worked example
A conductor experiences a force to the left in a fixed magnetic field. Predict the force if current reverses, then if both current and field reverse from the original setup.
- Keep conductor orientation fixed and identify the one change in the first case: current reverses.
- The motor-effect force therefore reverses to the right.
- For the second case start again from the original setup and reverse both current and field.
- Each reversal changes the force direction once, so two reversals restore the original leftward force.
Current reversal alone produces a rightward force; reversing both current and field produces a leftward force relative to the original setup.
Try together
A coil between magnetic poles begins to turn. Explain why reversing the coil current at each half-turn helps it keep rotating in one direction.
- Think about the coil sides swapping positions after half a turn.
- Name the component that changes the connection to the d.c. supply.
Show guided answer
The split-ring commutator swaps the coil connections each half-turn. The current in each side reverses as its position swaps, so the torque continues in the same rotational sense.
Practise independently
- Describe the magnetic field inside a long current-carrying solenoid.
Show answer and reasoning for question 1
It is strong and approximately uniform. The coiled wire concentrates the field and produces nearly parallel field lines inside.
- What happens to an electromagnet when its current is switched off?
Show answer and reasoning for question 2
Most of its magnetism disappears. Its field depends on current, though an iron core may retain some residual magnetism.
- What happens to motor-effect force if only the magnetic field reverses?
Show answer and reasoning for question 3
The force reverses direction. Current and conductor orientation are unchanged, so one field reversal reverses the force.
- What happens if both current and field reverse from the starting setup?
Show answer and reasoning for question 4
The force keeps its original direction. Two independent reversals cancel their effect on the force direction.
- State what each part of Fleming's left hand represents.
Show answer and reasoning for question 5
Thumb force, first finger field, second finger conventional current. The three directions are mutually perpendicular in the standard rule.
- What is the role of the split-ring commutator in a simple motor?
Show answer and reasoning for question 6
It reverses coil connections each half-turn. That maintains a turning effect in the same rotational direction as the coil turns.
DASKEREL exam-style practice · 8 draft marks
This original practice task and guidance are not an official examination-board paper or mark scheme.
Explain how a solenoid creates a useful field and how a simple d.c. motor keeps turning. Predict the force after reversing current only, then both current and field. (8 draft marks)
Show draft mark guidance
- State that current in a wire creates a magnetic field.
- Explain that a solenoid concentrates the field inside it.
- Identify the force on a current-carrying conductor in a field as the motor effect.
- Predict one current reversal reverses the force direction.
- Predict reversing both current and field restores the original force direction.
- Explain opposite coil sides experience opposite forces producing a turning effect.
- Identify a split-ring commutator as reversing the coil connections each half-turn.
- Explain that this reversal maintains rotation in the same sense, with brushes retaining contact.
Exit ticket
Answer without looking back, then check your reasoning.
- What happens to the conductor's force if only its current is reversed?
Show answer
The force reverses direction, assuming the field and conductor orientation stay the same.
- Why is a split-ring commutator used in a simple d.c. motor?
Show answer
It reverses the coil connections each half-turn so the turning effect continues in the same rotational direction.
Check your understanding
- A solenoid's field depends on current and can be switched off.
- Reversing both current and field gives the original force direction, not a double reversal of movement.
- The commutator reverses coil connection, not the permanent magnet's poles.
Retrieve later: Tomorrow, draw a solenoid and a simple motor and narrate what changes after half a turn without notes.
Next step: Apply the motor-effect direction rule to new diagrams and compare a motor with a generator at a later stage.
Library links: Oak National Academy · Electromagnetism (checked 2026-11-07) · DASKEREL subject library. Oak's applicable post-2022 content licence is OGL v3.0; some source assets have separate third-party rights. No Oak media is embedded here. DASKEREL is not affiliated with Oak.