DASKEREL published · Year 11 · academic review pending

Design and Technology GCSE

Original DASKEREL teaching informed by an attributed Oak unit sequence. This resource remains subject to qualified academic review. Check your examination board and tier before using it for exam preparation.

Year 11 · Original DASKEREL study pack · Academic review pending

Iterate a design from test evidence

Allow up to 55 minutes for reading, practice and review · Source route: Oak KS4 design and technology; board-neutral preparation

DASKEREL wrote this resource using the Oak National Academy unit sequence as a curriculum reference. It is a study pack, not a complete unit or an exam-board-approved course. Academic review remains pending.

You will learn to

  • Create a testable prototype hypothesis.
  • Distinguish test results from interpretation and recommend a controlled change.
  • Document an iteration that can be compared fairly with the first prototype.

Key terms: iteration · prototype · variable · criterion · feedback · evidence

Learn the idea

Iteration is a loop of making a candidate, testing it against criteria, interpreting the evidence and changing the design. It is not simply redrawing the same concept more neatly. Start with a problem statement and one measurable criterion. For a tabletop reading stand, the criterion might be that the stand holds a specified book at two agreed angles without sliding on the test surface. Record the book mass, surface and angle; otherwise a later test is hard to compare.

A prototype isolates a design idea. A card mock-up can test reach and geometry before a stronger material is selected. When the first version fails, describe the failure precisely: 'the rear support slips after 20 seconds at the steeper angle' is actionable; 'it looks weak' is not. If you change the support angle and add a rubber pad simultaneously, you cannot tell which change helped. Test one change where practical, then keep the same load and method.

User feedback can reveal requirements a bench test misses, such as difficulty folding the stand. Seek consent and ask neutral questions rather than 'isn't this better?'. Record the user's comment alongside objective measurements; one opinion is not proof for all users. Annotate version numbers, dimensions and reasons for decisions. Any manufacturing, tool use and assessed GCSE non-exam work require centre supervision, authenticity controls and the chosen board's current rules.

Worked example

A card reading stand holds a 0.8 kg book at 30° but slides at 45° on a smooth desk after 20 seconds. Plan a fair next iteration.

  1. Record the original base width, support angle, desk surface, book mass and time to slide.
  2. Hypothesise that increasing the rear support footprint will improve stability at 45°.
  3. Make version 2 with only that footprint change; keep the same card, book, desk and 45° test.
  4. Repeat the test and record time to slide, then compare with 20 seconds before deciding whether the change worked.

A traceable one-variable change makes the comparison more informative; it does not guarantee the stand is safe for general use.

Try together

A prototype holder is hard for one user to fold. Write a neutral feedback question and one measurable follow-up test.

  • Avoid suggesting the answer in the question.
  • Choose a repeatable task and record conditions.
Show guided answer

Ask: 'Which step in folding the holder was difficult, and why?' Then time a clearly defined folding task over repeated supervised trials with the same setup, recording errors as well as time.

Practise independently

  1. Why change only one design variable in the first retest when possible?
    Show answer and reasoning for question 1

    It helps attribute any changed result to the modified feature. Changing several features together makes causal interpretation weaker.

  2. Separate the observation and interpretation in 'the stand slipped because the base is too narrow'.
    Show answer and reasoning for question 2

    Observation: the stand slipped under stated test conditions. Interpretation: a narrow base may be a cause, which needs a test. A proposed cause is not yet established by a single observation.

  3. Name two conditions that must stay constant when comparing two stand versions.
    Show answer and reasoning for question 3

    For example, the same book mass and desk surface (also angle, test duration and loading position). Comparable conditions make the iteration evidence more meaningful.

DASKEREL exam-style practice · 5 draft marks

This original practice task and guidance are not an official examination-board paper or mark scheme.

A first prototype fails a stability test. Propose a controlled revision, explain how you would compare it with the first, and state one limitation. This is DASKEREL written practice, not a centre-authenticated NEA mark scheme.

Show draft mark guidance
  • 1 practice point: states the observed failure with test conditions.
  • 1 practice point: proposes a plausible single-feature change and reason.
  • 1 practice point: defines a repeatable success criterion.
  • 1 practice point: keeps relevant test conditions comparable.
  • 1 practice point: evaluates a limitation or further user/safety test.

Check your understanding

  • A new drawing without test evidence is not a demonstrated improvement.
  • A user's preference and a measured result answer different questions.
  • A successful small prototype test does not certify the final product's safety.

Retrieve later: Describe the four steps of an evidence-led iteration, then separate one observed failure from its possible cause.

Next step: Build a version log with photos or sketches, dimensions, test results and decisions under the centre's practical and NEA rules.

Library links: Oak National Academy · Iterative Design Principles (checked 2026-11-07) · DASKEREL subject library. Oak's applicable post-2022 content licence is OGL v3.0; some source assets have separate third-party rights. No Oak media is embedded here. DASKEREL is not affiliated with Oak.