Year 10 · Original DASKEREL extended lesson · Academic review pending
Circuit components and changing resistance
Allow up to 60 minutes for reading, practice and review · Source route: Oak AQA Physics Foundation; academic review required
DASKEREL wrote this resource using the Oak National Academy unit sequence as a curriculum reference. It is an extended lesson, not a complete unit or an exam-board-approved course. Academic review remains pending.
You will learn to
- Measure and calculate resistance from potential difference and current.
- Distinguish the I–V behaviour of an ohmic resistor, filament lamp and diode.
- Describe a valid low-voltage circuit investigation with appropriate controls.
Key terms: current · potential difference · resistance · ohmic conductor · filament lamp · diode · I–V characteristic
Teaching sequence
Check these ideas before you begin:
- Recognise a closed circuit and distinguish series from parallel connections.
- Rearrange or use R = V ÷ I and plot ordered pairs on labelled axes.
1. Retrieve circuit quantities · about 8 minutes
Teach or study: Elicit the units and the correct placement of ammeter and voltmeter from prior circuit work.
Try: Label the current and voltage readings on a simple circuit diagram.
2. Model resistance at a point · about 12 minutes
Teach or study: Calculate two lamp resistances and distinguish an operating-point ratio from a fixed material property.
Try: Calculate R from two V–I pairs and compare the results with units.
3. Read characteristic shapes · about 14 minutes
Teach or study: Compare a straight ohmic line, a bending lamp trace and one-way diode response without claiming exact thresholds.
Try: Match three described graph shapes to components and justify each choice.
4. Plan and practise · about 18 minutes
Teach or study: Model a low-voltage supervised setup and ask how temperature could distort the resistor comparison.
Try: Complete the guided calculation and independent checks before viewing feedback.
5. Exit and correct · about 8 minutes
Teach or study: Ask learners to correct a claim that all components have constant resistance at every voltage.
Try: Answer two exit prompts and revise one graph interpretation.
Learn the idea
Current is the rate of flow of electric charge and is measured in amperes, A. Potential difference, measured in volts, V, is the energy transferred per unit charge between two points. Resistance describes opposition to current and can be calculated for a particular operating point from R = V ÷ I, with R in ohms when V is in volts and I in amperes. The equation works at a measured point even if a component's resistance changes when conditions change. It does not mean every component has one fixed resistance for all applied potential differences.
For an ohmic resistor held at approximately constant temperature, current is directly proportional to potential difference. On an I–V graph with potential difference on the horizontal axis and current on the vertical axis, its points form a straight line through the origin. A doubling of potential difference doubles current, so V/I remains constant. If the resistor heats appreciably, this simple model may no longer fit. Specify constant temperature when identifying ohmic behaviour rather than inferring it from a single reading. One point alone cannot reveal the shape of a component's characteristic.
A filament lamp behaves differently. Increasing the potential difference increases current and heats the metal filament. The hotter filament has greater resistance, so the current rises by a smaller amount for each further increase in voltage. Its I–V graph bends and becomes less steep on the positive side. The graph is not a straight line, even though R = V/I can still be evaluated at any non-zero point. For example, at 2 V and 0.40 A the resistance is 5 Ω; at 4 V and 0.50 A it is 8 Ω. The comparison shows a change in resistance as the lamp warms.
A diode largely allows current in one direction and has very high resistance in the reverse direction. In the forward direction, appreciable current begins after a characteristic threshold; the exact threshold depends on the diode and the measured circuit. A reverse reading close to zero current is not proof of infinite resistance or perfect blocking. Thermistors and light-dependent resistors are also variable components: the resistance of a typical NTC thermistor decreases as temperature rises, and LDR resistance decreases as light intensity rises. Describe the changed condition explicitly rather than saying all resistance falls when current rises.
To investigate I–V characteristics, use a low-voltage supply and a circuit diagram checked by a teacher. Put the ammeter in series with the component and the voltmeter in parallel across it. Adjust the potential difference in small steps, record paired V and I readings, and change polarity only under supervision if negative readings are required. Keep an ohmic resistor at roughly constant temperature; take care because a filament can warm. Plot signed values on labelled axes, assess the shape, then calculate R at selected non-zero points. Do not connect this classroom circuit to mains electricity. A fair comparison controls the component and measurement method while changing potential difference.
Worked example
A filament lamp is measured at 2.0 V, 0.40 A and at 4.0 V, 0.50 A. Calculate both resistances and interpret the change.
- At the first point, R = 2.0 ÷ 0.40 = 5.0 Ω.
- At the second point, R = 4.0 ÷ 0.50 = 8.0 Ω.
- The potential difference doubles but current does not, so the characteristic is not ohmic over these points.
- The filament heats and its resistance rises; the two calculated values are operating-point resistances.
Resistance rises from 5.0 Ω to 8.0 Ω as the lamp operates at higher potential difference.
Try together
For a component, readings are 1.5 V and 0.30 A, then 3.0 V and 0.60 A. Calculate both resistances and say whether the data are consistent with an ohmic resistor.
- Divide each potential difference by its matching current.
- Compare the ratios, but note that two points do not prove behaviour at every value.
Show guided answer
Both ratios are 5 Ω. The two readings are consistent with constant resistance over this range, but more points and temperature control are needed to establish a straight I–V relation.
Practise independently
- What is the unit of electrical resistance calculated from V ÷ I?
Show answer and reasoning for question 1
The ohm, Ω. A potential difference in volts divided by current in amperes gives ohms.
- Calculate resistance when a component has 6 V across it and 2 A through it.
Show answer and reasoning for question 2
3 Ω. R = V ÷ I = 6 ÷ 2 = 3 ohms at that operating point.
- Why does a filament lamp's resistance often rise as voltage rises?
Show answer and reasoning for question 3
Its filament gets hotter. A hotter metal filament resists the charge flow more strongly.
- Where should the voltmeter connect to measure potential difference across a lamp?
Show answer and reasoning for question 4
In parallel across the lamp. It compares the electrical potential on the two sides of the component.
- What does a nearly zero reverse current through a diode suggest?
Show answer and reasoning for question 5
The diode strongly opposes reverse current. It does not establish a mathematically infinite resistance or a perfect block.
- Why is one V–I reading insufficient to identify an ohmic component?
Show answer and reasoning for question 6
It gives no evidence of the overall graph shape. Direct proportionality must be checked across multiple paired readings at controlled temperature.
DASKEREL exam-style practice · 8 draft marks
This original practice task and guidance are not an official examination-board paper or mark scheme.
A lamp gives 2 V, 0.4 A and 4 V, 0.5 A. Calculate two resistances, compare their values and outline a safe, valid I–V investigation. (8 draft marks)
Show draft mark guidance
- Use R = V ÷ I for the first reading.
- Calculate 5 Ω at 2 V and 0.4 A.
- Use R = V ÷ I for the second reading.
- Calculate 8 Ω at 4 V and 0.5 A.
- State that lamp resistance increased.
- Connect the ammeter in series and voltmeter across the lamp.
- Use a low-voltage supply and vary potential difference in steps under supervision.
- Record paired readings and plot labelled I–V axes or control a relevant condition.
Exit ticket
Answer without looking back, then check your reasoning.
- A lamp is at 3 V and 0.50 A. Calculate its resistance at that point.
Show answer
R = 3 ÷ 0.50 = 6 Ω at that operating point.
- Where do an ammeter and a voltmeter go when measuring one component?
Show answer
The ammeter goes in series; the voltmeter goes in parallel across the component.
Check your understanding
- R = V/I can calculate an operating-point resistance without implying resistance is constant.
- A diode has high reverse resistance, but near-zero measured current is not proof of a perfect open circuit.
- An ammeter is connected in series, while a voltmeter is connected in parallel.
Retrieve later: Tomorrow, sketch three qualitative I–V traces and label the resistor, filament lamp and diode with a reason for each.
Next step: Apply these characteristics to simple sensing circuits, then revisit the required-practical method with a teacher.
Library links: Oak National Academy · Circuit components (checked 2026-11-07) · DASKEREL subject library. Oak's applicable post-2022 content licence is OGL v3.0; some source assets have separate third-party rights. No Oak media is embedded here. DASKEREL is not affiliated with Oak.